We also offer installation & fitting support. Ask us about fitting.
Add an aftermarket NTSC reversing camera to selected Chrysler, Dodge, Fiat and Lancia vehicles with a Uconnect 5-inch or 8.4-inch RB5/RE2 factory system and 22-pin connections.
The interface codes and activates the original camera input, automatically displays the camera when reverse gear is selected and provides a switched 12V camera-power output rated at up to 500mA. The original factory AUX connections are retained.
Add an aftermarket reversing camera to the original factory display in selected Chrysler, Dodge, Fiat and Lancia vehicles.
This interface is designed for compatible vehicles equipped with a Uconnect 5-inch or 8.4-inch RB5/RE2 factory system using white and grey 22-pin connections behind the original head unit.
When correctly installed and coded, the original display automatically changes to the aftermarket reversing-camera image when reverse gear is selected. A switched 12V output rated at up to 500mA is provided to power a compatible camera while reversing.
Important: The interface supports NTSC cameras and video sources only. Compatibility must be confirmed from the original Uconnect system and 22-pin rear connections before ordering.
This interface activates the factory reversing-camera input on compatible Uconnect 5-inch and 8.4-inch infotainment systems.
It allows the original factory radio and display to be retained while adding an automatically activated aftermarket reversing camera.
Chrysler:
Dodge:
Fiat:
Lancia:
The installation guide also identifies selected Jeep applications using the same Uconnect system. As no specific Jeep models are listed on the current product page, compatibility must be confirmed by checking the factory system and rear connections before ordering.
Similar-looking Uconnect systems can use different connections and interface technology. Check the original head-unit model and rear connectors before ordering.
When reverse gear is selected, the interface automatically activates the factory camera input and displays the aftermarket reversing-camera image on the original Uconnect screen.
When reverse gear is disengaged, the camera-power output switches off and the display returns to the previously selected factory function.
The aftermarket reversing camera’s male RCA video plug connects to the female RCA camera input on the supplied interface harness.
The white output wire provides a switched 12V supply rated at up to 500mA. Power is supplied while reverse gear is engaged and switches off when the system leaves the reversing-camera mode.
Cameras requiring more than 500mA must be powered through a suitable separate fused supply and relay.
The red and white RCA connectors on the interface harness carry the vehicle’s original factory AUX audio signal and must remain connected.
The yellow male RCA connector shown on the harness is not used for this installation.
After installation, the factory Uconnect camera input must be coded using the interface DIP switches.
Once coding is complete, the reversing-camera input should activate automatically when reverse gear is selected.
The interface includes video-in-motion functionality for compatible original factory video equipment.
The function may be configured for permanent operation or controlled selectively using the supplied green wire and an additional switch.
The optional control switch is not included. This function applies only to compatible factory video content and does not add a separate aftermarket video input.
The interface is installed behind the factory monitor or head unit.
The vehicle’s original white and grey 22-pin connectors are disconnected from the head unit and connected to the corresponding connectors on the interface harness. The interface harness then connects back into the original head unit.
The supplied CAN-box connects to the interface harness through its 8-pin Molex connection. The camera video cable connects to the female RCA camera input and the camera may be powered from the switched 12V output, subject to the 500mA maximum rating.
The red and white factory AUX RCA connections must remain connected after installation.
Vehicle wiring colours and connector assignments can change during production. Every connection must be tested and confirmed by the installer.
Professional installation by an experienced vehicle-electronics or car-audio technician is strongly recommended.
Check the vehicle model, production year, Uconnect screen size, factory system code and original rear connectors before ordering.
Moving video must not be viewed by the driver while the vehicle is being driven. The driver must remain focused on the road at all times.
Video-in-motion functionality should only be used by passengers where legally permitted. While driving, the screen should only display appropriate fixed menus or reversing-camera images that assist safe vehicle operation.
Brand: InCarTec
Car models: The years stated refer to the model's years of manufacture, please check the item description for information about any changes there may be within these productions years.
Chrysler - 300C 2nd Gen (LX)* (2011 >)
Dodge - Journey (2008 - 2010)
© Copyright 2026 InCarTec. All Rights Reserved