We also offer installation & fitting support. Ask us about fitting.
Add an aftermarket NTSC reversing camera to selected Chrysler, Dodge, RAM and Jeep vehicles with a Uconnect 5-inch, 8.4A RA3 or 8.4AN RA4 factory system and 52-pin connection.
The interface codes and activates the factory camera input, automatically displays the camera when reverse gear is selected and provides a switched 12V camera-power output rated at up to 500mA. Factory AUX connections are retained.
Add an aftermarket reversing camera to the original factory display in selected Chrysler, Dodge, RAM and Jeep vehicles.
This interface is designed for compatible vehicles equipped with a Uconnect 5-inch, 8.4A RA3 or 8.4AN RA4 factory infotainment system using a 52-pin connection behind the original head unit.
When correctly installed and coded, the original display automatically changes to the aftermarket reversing-camera image when reverse gear is selected. The interface also provides a switched 12V output rated at up to 500mA to power a compatible camera while reversing.
Important: This interface supports NTSC cameras and video sources only. Check the exact Uconnect system and confirm that the original head unit has the required 52-pin connection before ordering.
This interface activates the factory reversing-camera input on compatible Uconnect 5-inch and 8.4-inch infotainment systems with a 52-pin connection.
It allows the original radio and display to be retained while adding an automatically activated aftermarket reversing camera.
Chrysler:
Dodge:
RAM:
Jeep:
All vehicles must have a compatible Uconnect 5-inch, 8.4A RA3 or 8.4AN RA4 factory system with a 52-pin connection.
Similar-looking Uconnect systems may use different connections. This interface is not interchangeable with the 22-pin Uconnect camera interface.
When reverse gear is selected, the interface automatically activates the original camera input and displays the aftermarket reversing-camera image on the factory Uconnect screen.
When reverse gear is disengaged, the switched camera-power output turns off and the display returns to the previously selected factory function.
The aftermarket reversing camera’s male RCA video plug connects to the female RCA camera input on the supplied interface harness.
The white output wire provides a switched 12V supply rated at up to 500mA. This output is active while reverse gear is selected and switches off when the camera display closes.
Cameras requiring more than 500mA must be powered through a suitable separate fused supply and relay.
The red and white RCA connectors on the interface harness carry the vehicle’s original factory AUX audio signal and must remain connected.
The yellow male RCA connector shown on the harness is not used for this installation.
After installation, the factory Uconnect camera input must be coded using DIP switch 2 on the supplied CAN-box.
Once coding is complete, the reversing-camera input should activate automatically when reverse gear is selected.
The interface includes video-in-motion functionality for compatible original factory video equipment.
The function can be configured for permanent activation or controlled selectively using the supplied green wire and an additional switch.
The optional switch is not included. This feature applies only to compatible original factory video content and does not add a separate aftermarket video input.
The interface is installed behind the factory monitor or head unit.
The vehicle’s original female 52-pin connector is disconnected from the factory system and plugged into the male connector on the interface harness. The female 52-pin connector on the interface harness then connects to the original head unit.
The CAN-box connects to the interface harness through its 8-pin Molex connection. The camera video cable connects to the female RCA socket and the camera may be powered from the switched 12V output, subject to its 500mA maximum rating.
The red and white factory AUX RCA connections must remain connected following installation.
Vehicle wiring colours and connector assignments may change during production. Every connection must be tested and confirmed by the installer.
Professional installation by an experienced vehicle-electronics or car-audio technician is strongly recommended.
Check the vehicle model, production year, Uconnect screen size, factory system code and original 52-pin connector before ordering.
Moving video must not be viewed by the driver while the vehicle is being driven. The driver must remain focused on the road at all times.
Video-in-motion functionality should only be used by passengers where legally permitted. While driving, the screen should only display appropriate fixed menus or reversing-camera images that assist safe vehicle operation.
Brand: InCarTec
Car models: The years stated refer to the model's years of manufacture, please check the item description for information about any changes there may be within these productions years.
Jeep - Cherokee 5th Gen (KL) (2014 - 2023)
© Copyright 2026 InCarTec. All Rights Reserved